OTC SMART CARD CRACK SERIAL
I would check your power supply as it should power up but if battery to dead it won't do nothing! I know you had 2 ways to update, 1 was to use a flash usb stick and also with the serial cable but that was dropped for updates and they now use external flash reader to update card. Also there is a coin battery inside the Genisys to retain settings and such easily replaceable with time. I have a genisys with bad battery and it takes a bit with power to get battery up enough to boot so might want to find way to get an RC car charger and physically remove battery and charge it.
OTC SMART CARD CRACK SOFTWARE
So let me understand what you did with genisys.you installed the software on your computer (what version windows) and once it updated now it will not power on, correct? Does it make a beep or anything? Usually no power up is due to dead battery so be sure battery is up. I have the smart inserts cable, as the 'smart cable' only works with 3.0 and up. There is a 32MB card inside, and a 512MB outside.
Any help you could provide with the Genisys would be great. The more I think about it, I should have just bought the TSI/VSI cartridges for my SnapOn. I bought the Genisys because I was looking for a better tool that I could also update. I also have a SnapOn MT2500, but the cartridges aren't current enough to have that option. As it is now, the Jeep is throwing a B1 lean code.
I was told I need to set my fuel sync to +6 or so for use with the cam. I rebuilt the motor a few months ago, and built it with a mild Comp cam. Anyway, I'm working on my 96 Jeep Grand Cherokee, 4.0L, 42RE, 4WD. I could see if I could get it to at least power up, I could recover it or something, but the tool now does nothing. OTC says no repair on these, so I guess I am stuck with an expensive piece of plastic. I don't have the wall wart for it.) Power was provided by my 12v power supply for my amateur radio. I'm on external power (through the cable w/ the lighter adapter. Went to turn it on, and now the damn thing won't even power up. Came back to it later, and it SId it was done, and the tool was powered off. It found updates, and took 3 hours to do it. I installed it on my computer, and then ran the update. Well, I contacted the seller, and he had the CD, and sent it to me. What are you trying to do fuel sync on what year, model, engine Jeep? Are you Using the 'smart cable with no adapters' or still the smart inserts? I will try to help if I can with what I know with the Genisys. I do not use mine as much since I now have Snap on Modis and now use the Genisys at home. What size memory card do you have? Is it only domestic or other programs on it? I can probably find the cd but if I know what you are trying to do I might be able to help.Īlso you can find out the version or the different software in the tool menu (not sure right now since I do not have in front of me) usually it starts with version 1.0 and I can find updated file for what you have. Even though it is the first version (which I had until it needed a repair) it can run the later software as long as you have the proper cables. If the unit was updated there is not much else you would need it for. What also sucks is that I bought this thing, and I still can't do the fuel sync on my damn Jeep! I have numerous versions of the older Genisys software but why do you want the CD? My tool has Pathfinder 2004 on it, and the ext memory card. What I am looking for is someone who has a version 1 Genisys, that has the CD still. I called OTC and they told me that they don't even make the CD anymore, but that if I can find someone who has a older tool, that I can get the CD from them. I picked up a OTC Genisys from eBay for a fairly good price, and while it works, I am trying to find the CD that came with it.
0 kommentar(er)
